Removal
System Cover
Identify the system cover highlighted in blue.
Using a flat head or a Phillips screwdriver, rotate the lock counter clockwise.
Lift the latch until the system cover slides back.
Hold the cover on both sides, and lift the cover away from the system.
Front Bezel
Identify the front bezel highlighted in blue.
Unlock the front bezel by using the key.
Press the release button and disengage the left end of the bezel.
Unhook the right end, and remove the front bezel.
Drive backplane cover
Identify the drive backplane cover highlighted in blue.
Slide the drive backplane cover to the rear of the system.
Lift the drive backplane cover from the system.
Air shroud
Identify the air shroud highlighted in blue.
Holding the edges of the air shroud, lift the air shroud out of the system.
Cooling fan cage assembly
Identify the cooling fan cage assembly highlighted in blue.
Rotate the blue release levers to unlock the cage assembly from the system.
Hold the release levers, and lift the cooling fan cage assembly away from the system.
Side wall brackets right
Identify the side wall brackets highlighted in blue.
Press the tabs to release the side wall cable holder.
Move the cables out of the side wall cable holder and observe the cable routing.
Press the center tab to release the bracket from the chassis, and lift it away from the system.
BOSS-N1 Module
Identify the BOSS-N1 Module highlighted in blue.
Remove the BOSS-N1 power and signal cable from the BOSS-N1 module.
Remove the screw that secures the BOSS-N1 module on the riser 1.
Slide the BOSS-N1 module toward the front of the chassis and lift the module.
Riser 1B
Identify the riser 1B highlighted in blue.
Using a Phillips screwdriver, loosen the blue thumb screw on the riser.
Disconnect any cables that are connected to the expansion card or the riser.
Press the blue release tab or blue button on the riser.
Holding the edges, lift the expansion card riser from the riser connector on the system board.
Control panel - Right
Identify the control panel highlighted in blue.
Remove the screws that secure the control panel cable cover to the system.
Remove the cable cover away the system.
Disconnect the right control panel cable and the VGA cable from the connectors on the system board.
Remove the screws that secure the control panel assembly to the system.
Holding the cable, slide the right control panel out of the system.
Install
Control panel - Right
Identify the control panel location highlighted in blue.
Align the right control panel assembly with the slot and slide into place.
Install the screws to secure the control panel to the system.
Connect the right control panel cable and VGA cable to the connectors on the system board.
Route the control panel cable through the side wall of the system.
Align and slide the right control panel cable cover in the slot on the system.
Install the screws to secure the control panel cable cover to the system.
Riser 1B
Identify the riser 1B location highlighted in blue.
Holding the edges, insert the riser into place and press the touch points until the riser is fully seated.
Using a Phillips screwdriver, tighten the blue thumb screw to secure the riser on the chassis.
Connect the cables to the expansion card on the riser.
BOSS-N1 Module
Identify the BOSS-N1 Module location highlighted in blue.
Install the BOSS-N1 module and push horizontally towards the rear of the system untill firmly seated.
Install the screw that secures the BOSS-N1 module to the riser 1.
Connect the BOSS-N1 power and signal cables to the connectors on the BOSS-N1 module.
Side wall brackets right
Identify the side wall brackets location highlighted in blue.
Align and slide until the side wall brackets is seated firmly.
Close the side wall cable holder until the holder clicks into place.
Cooling fan cage assembly
Identify the cooling fan cage assembly location highlighted in blue.
Align and place the cooling fan cage assembly into the system until seated firmly.
Rotate the blue release levers to lock the cooling fan cage assembly into the system.
Air shroud
Identify the air shroud location highlighted in blue.
Tilt at an angle and align the tabs with the slots on the system and place the air shroud until it is firmly seated.
Drive backplane cover
Identify the drive backplane cover location highlighted in blue.
Align and place the drive backplane cover on the system.
Slide the drive backplane cover to the front of the system until it fits into place.
Front Bezel
Identify the front bezel location highlighted in blue.
Align and insert the tabs on the bezel into the slots on the system.
Press the bezel until the release button clicks in place.
Lock the front bezel by using the key.
System Cover
Identify the system cover location highlighted in blue.
Align the tabs on the system cover with the guide slots on the system and slide the system cover.
Close the system cover release latch.
Using a flat head or Phillips screwdriver, rotate the lock clockwise to the lock position.